3000L SS mother-daugher system tank
  1. Home
  2. »
  3. custom container
  4. »
  5. How to ship custom, not standard sized containers?

Table of Contents

Picture of Ivy Wang

Ivy Wang

Hi, I‘’m Ivy Wang, Co-Founder of Leeta Metals. I've been in stainless steel IBCs and custom shipping containers for more than 10 years. I'm glad to share useful industrial knowledge with you. If you need any custom solutions, please feel free to contact us any time!

IBC Mother–Daughter System:

Specifying 3,000 L Stainless Steel IBCs for Water-Treatment Chemicals

Case study · stainless steel IBC totes · dangerous-goods classification · liner selection · mother–daughter tank configuration · ASME connections

A client recently came to us with what looked like a simple request — “we need nine 3,000-litre stainless steel IBC totes, please quote.” We could have quoted. But a tank is only ever as good as its match with the liquid inside it, and at that first conversation we didn’t yet know what that liquid would be.

So before proposing anything, we did what we always do: we talked the requirement through with the client until we understood what they actually wanted to store, how it would be transported, where the tanks would end up, and how the installation was arranged. Only then did we open the Safety Data Sheets and start engineering. This post walks through that process — from a client’s one-line requirement to a fully justified solution — step by step. If you buy or specify IBCs for chemicals, the checklists here should save you a round of quotations — and possibly a returned shipment.

STEP 1

Start With the Chemistry, Not the Catalogue

Before proposing a single tank, we asked the client one question: what exactly will be stored in them?

The answer: three water-treatment chemicals, all supplied by the same chemical vendor and all destined for the same dosing station:

  • Product A — an antiscalant (scale inhibitor for water systems)
  • Product B — a corrosion inhibitor
  • Product C — a non-oxidizing biocide

With the stored products confirmed, we pulled the Safety Data Sheet (SDS) of each one and went straight to two sections: Section 14 (transport) and Section 7 (handling & materials). These two pages decide more about a tank than any price list ever will. Here is what the transport sections told us:

Table 1 · Transport classification at a glance (per manufacturer SDS)
Product Function Transport status UN No. Hazard class Packing group Marine pollutant
A · Antiscalant Scale control NOT A DANGEROUS GOOD
Not regulated by sea (IMDG), land (ADR/DOT) or air (IATA)
— — — No
B · Corrosion inhibitor Corrosion control DANGEROUS GOOD · PG III UN 3265 Class 8 (Corrosive) Packing Group III No
C · Non-oxidizing biocide Microbiological control DANGEROUS GOOD · PG II UN 3265 Class 8 (Corrosive) Packing Group II Yes — IMDG Marine Pollutant

How to read the packing groups

Products B and C share the same UN number (3265) and the same hazard class (8, corrosive liquid, acidic, organic). The difference is the packing group — and within a UN number, PG I is the most severe, PG II middle, PG III the mildest. A PG II package must pass tougher drop, stack and leak-proofness tests than a PG III one. Product C also carries the Marine Pollutant mark for sea freight, which affects documentation and labelling.

Practical consequence: only two of the three liquids need UN-certified dangerous-goods packaging at all. The antiscalant can ship as general cargo. And when a tank is installed as fixed storage equipment rather than shipped full as a transport package, it falls outside the UN packaging system entirely — a distinction we raise with every chemical-storage client, in writing, before anyone quotes “UN-certified IBC” pricing.

A quiet but important detail: while reviewing the client’s documents we noticed one SDS file was named after one product code but carried a different code inside the document (the file said 437, the SDS said 237). We flagged it back to the client before going further. Always check that the file name, the product name and the product code inside the SDS all agree — a mismatched SDS is how wrong material selections get made with full confidence.

STEP 2

316 Stainless — or 304 with a Liner? Let the SDS Decide

The client had two constructions in mind and asked for both. We tested each against the SDS — and the SDS answered the question for us.

In early discussions the client mentioned the two options they were considering: a bare 316 stainless steel tank, and a 304 stainless steel shell with a plastic liner. Instinct says “316 is the higher alloy, so it must be safer.” The SDS says otherwise.

The biocide (Product C) is the decisive case. Its GHS classification includes Corrosive to metals, Category 1, and — critically — Section 7 of its SDS lists the unsuitable materials in black and white:

Table 2 · What the biocide SDS says about construction materials
Listed as SUITABLE (Section 7) Listed as UNSUITABLE (Section 7)
HDPE · PTFE · Perfluoroelastomer · PVDF · Polypropylene · Rigid CPVC · Plexiglass Carbon steel · 304 stainless steel · 316L stainless steel

Read that right-hand column again: both 304 and 316L are on the “do not use” list. The isothiazolinone biocide in an acidic pH 2–5 blend attacks stainless steel by pitting — stepping up from 304 to 316 does not rescue you. The SDS explicitly requires storage “in a container with a corrosion-resistant lining.”

The corrosion inhibitor (Product B, pH ≈ 1.4) is a polycarboxylic-acid polymer whose SDS lists 304 as suitable — so bare stainless is fine for it and for the near-neutral antiscalant.

Table 3 · Material options vs. the three media
Construction Antiscalant A Corrosion inhibitor B Biocide C Verdict
Bare 316 SS ✔ OK ✔ OK (SDS lists 304 as suitable; 316 is a step up) ✘ NOT OK (SDS lists 316L as unsuitable) Works for A + B only
304 SS shell + plastic liner ✔ OK ✔ OK ✔ OK if liner is HDPE (named in SDS) or a confirmed-compatible plastic The only single construction that holds all three

How we presented the solution: two parallel lines, clearly labelled — 304 + liner as the all-compatible recommended option, and bare 316 as an option limited to Products A + B, each backed by the relevant SDS page. Matching the construction to the chemistry — instead of defaulting to the highest alloy — costs nothing and builds trust; recommending “316 for everything” would have cost the client a tank.

STEP 3

PE or PVC Liner? The Answer Is a Manufacturing Story, Not a Chemistry Story

The client’s shortlist included both liner polymers. “Which plastic is more chemical-resistant?” is the wrong first question. The right one is: “which plastic can be made into a large lining reliably?”

Here is the part most buyers never see — and the part we explained to the client before recommending one: the polymer decides the process, and the process decides the quality.

Why PE can be rotomoulded — and PVC cannot

  • HDPE melts at roughly 125–135 °C and does not significantly decompose until above 300 °C. That wide window is exactly what rotational moulding needs: PE powder is charged into the welded steel shell, the whole vessel rotates in an oven at 250–340 °C for 30–60 minutes, and the powder melts and coats the inner wall as one continuous, seamless layer. Quality is set by the machine program.
  • Rigid PVC softens at 80–100 °C but starts decomposing — releasing HCl, discolouring, embrittling — at around 150 °C. Its usable processing window is only about 20–25 °C wide, nowhere near enough for a long oven cycle. So a PVC lining can only be made cold: sheets are cut, thermoformed against the wall, and joined seam by seam with a hot-air gun and welding rod — roughly one weld seam every 1–1.5 metres, each one dependent on the welder’s hands.
Table 4 · HDPE rotolining vs. PVC sheet lining, side by side
HDPE (rotomoulded liner) PVC (sheet-welded liner)
Process Rotational moulding — one-piece, machine-controlled Sheet thermoforming + hand welding
Seams / failure points None — continuous layer One welded seam every 1–1.5 m; seams are the classic leak origin
Consistency Batch-to-batch set by equipment Operator-dependent
Supply base Very large — rotolining is a mainstream industrial process Narrow — skilled chemical-grade sheet welders are scarce
Where PVC/CPVC genuinely wins Strongly oxidising media (hypochlorite, nitric acid) and higher temperatures (CPVC to ~90 °C vs. HDPE 60–70 °C long-term)

And the oxidising-acid worry? Checked — it does not apply here

PE’s known weak spot is strong oxidising acids, and we would not recommend a liner we hadn’t stress-tested against the stored media. So we audited all three products for exactly that:

  • Antiscalant A (pH 2.4–3.6): its own SDS lists strong oxidisers as incompatible — it is the victim of oxidation, not an oxidiser.
  • Corrosion inhibitor B (pH 1.4): a polycarboxylic-acid polymer — an organic carboxylic acid, which is a completely different family from oxidising acids (nitric, chromic, perchloric). Low pH ≠ oxidising.
  • Biocide C: literally named non-oxidizing. Its blend does contain 1–5 % magnesium nitrate — the only oxidiser-family ingredient in the set — but as a dilute salt in water, and the SDS itself names HDPE as suitable, so the manufacturer has already signed off on exactly this combination.

Bottom line: HDPE is the only commodity plastic explicitly named as suitable in the biocide SDS. That paper evidence, plus the seamless process, is why we recommended 304 shell + rotomoulded HDPE liner as the primary option — with the PVC/CPVC option quoted alongside for customers whose own specification demands it (and with a written liner-manufacturer compatibility statement required in that case, since PVC itself is not on the SDS list).

STEP 4

The Mother–Daughter Configuration — the Heart of the Solution

As our discussion with the client deepened, they shared one more requirement — and it turned out to shape the whole installation: “supports suitable for putting a standard 1’000 L plastic IBC on top of the 3’000 L SS tote as mother-daughter configuration.”

What “mother–daughter” means here

Mother–daughter configuration is standard industry vocabulary for a large main vessel (the mother) with a smaller dosing or day tank (the daughter) mounted above or beside it, so concentrate or make-up chemical feeds down into the mother by gravity. The client’s wording told us three things at once:

  • The daughter is not a custom tank — it is a standard 1,000 L plastic IBC (the ubiquitous 1,200 × 1,000 mm footprint tote). Nothing to fabricate; only something to support.
  • The word supports (plural) means the deliverable is a steel support structure, not a vessel.
  • The phrase if necessary told us the client was delegating the engineering judgement to us — which is exactly the kind of question we like: our job was to decide how the daughter stands on the mother, and be able to defend every millimetre of it.

The physics problem: 1.2 tonnes on a 2–3 mm lid

A standard 1,000 L plastic IBC weighs roughly 1.1–1.3 t when full. The top plate of a 3,000 L stainless IBC is typically only 2–3 mm thick, and its top-corner stacking blocks are designed to carry an identical steel tote, not a plastic IBC whose base skeleton bears on different points. Setting the daughter directly on the tote top would deform the lid. There are three classical answers:

Table 5 · Three ways to carry a daughter IBC
Option Load path Effect on the mother tote Our verdict
1. Free-standing frame, legs to the floor Daughter → deck → legs → ground. Tote top carries zero load. None — the mother is supplied as standard RECOMMENDED
2. Frame clamped onto the tote top Through the tote top frame Requires a reinforced, load-bearing top — a spec change, a cost, a lead time Only if the customer insists
3. Platform / ring beam welded to the tote Through added structure on the tote body Most invasive modification of the mother Most integrated look, most work

The support frame we engineered — with real numbers

Having confirmed the mother tote’s true envelope with the factory (1,402 × 1,402 × 1,958 mm) and the standard daughter’s footprint (1,200 × 1,000 mm, ≈ 1,145 mm high), the free-standing frame writes itself — but the geometry has one trap worth explaining.

Because the legs must reach the floor, they must pass outside the mother tote. A frame whose legs sat on the 1,402 mm outline would collide with the tote body. So the frame outline must be larger than the mother — we chose 1,600 × 1,600 mm, which leaves ≈ 39 mm of clearance on each side between the leg inner face and the tote wall: enough for weld seams, lifting lugs and minor fitting projections, without making the frame absurdly wide.

Table 6 · Free-standing support frame — specification (one complete set)
Overall plan (outer envelope) 1,600 × 1,600 mm including leg section — column centre distance 1,540 mm, inner clear width 1,480 mm
Legs 4 × square tube 60 × 60 × 4 mm, length 2,100 mm, plumb to floor
Deck Bolted rail deck, deck top at 2,100 mm — beam soffit clears the 1,958 mm tote top by ≈ 42 mm
Daughter seating area 1,200 × 1,000 mm, framed by 40 × 40 × 4 mm locating stops, 50 mm high, on all four sides (anti-slide)
Base plates 4 × 150 × 150 × 8 mm, drilled for floor anchoring
Load path All ≈ 1.2 t of the full daughter goes directly to the ground; the mother’s top plate carries no load
Material / finish Carbon steel, painted or hot-dip galvanised
Construction & shipping Bolted, knock-down design; shipped loose, assembled on site
Assembled height 2,100 (deck) + 1,145 (daughter) ≈ 3,245 mm

Two details that quietly decide whether this works:

① The 100 mm lesson. Our first draft put the deck top at 2,000 mm. Then we drew the beams: a beam with a 100 mm section has its soffit at 1,900 mm — below the 1,958 mm tote top. Interference. This is precisely why we draw before we quote: the fix was to raise the deck so the beam soffit clears the tote top. Every millimetre of this frame is a negotiation between three fixed numbers (tote height, beam depth, daughter height).

② It cannot ship assembled. 3,245 mm exceeds container internal height (~2,690 mm for a 40’HC). The frame must be bolted, not welded, shipped as loose components, and assembled on site. If this is not written into the quotation and the packing plan, the container maths fails at the port, not at the drawing office.

And the “sister” tanks? Once one mother–daughter pair exists, scaling out is natural: several mother totes fed from one dosing station behave as a sister group — identical units sharing the same daughter logic, valves and controls. Designing the frame as a standard module (one drawing, nine frames) is exactly what keeps that multiplication cheap: the installation calls for nine totes, so we priced the frame per set and per nine sets, leaving the final count to the client’s confirmation.

STEP 5

“Connections Must Be ASME” — When the Project Is in the USA

Somewhere between the liner discussion and the frame drawings, the client added one quiet line — “since the project is in USA the connections must be ASME” — that decides every nozzle on the tank. It means more than “American threads.”

European tank practice defaults to EN/DIN flanges (the PN system). US plant piping is built on the ASME B16.5 class system. The two families have roughly convertible pressure ratings (Class 150 ≈ PN20, Class 300 ≈ PN50) but completely non-interchangeable dimensions — bolt circles, bolt counts and flange diameters all differ. A PN16 flange will simply not bolt up to American pipework.

Table 7 · European habit vs. US requirement
Item European default US / ASME requirement
Flanges EN 1092-1 (PN series) — Chinese equivalent GB/T 9119 ASME B16.5 (Class 150/300…) — Chinese equivalent HG/T 20615
Pipe threads ISO 228 G-threads or ISO 7 R-threads (55°) ASME B1.20.1 NPT (60° taper) — Chinese equivalent GB/T 12716
Material designations EN / GB grades ASTM grades (e.g. A182 F304/F316, A105)
Welding qualification ISO 15614 typical ASME IX (WPS/PQR) if required

NPT deserves its own warning: NPT and R threads share a 1:16 taper, so the first few turns engage smoothly — and then the 60° vs 55° flank angles fight each other. Seized threads or a weeping joint are the usual outcomes. “Looks like it fits” is the most expensive phrase in piping.

What we asked the client to confirm before pricing: which ASME standard applies to the connections (B1.20.1 threads or B16.5 flanges); the pressure class and facing (150#/300#, RF/FF); whether sizes are stated in NPS or DN; and the nozzle list (position, size, service). One more thing we stated rather than asked: we understood the requirement to apply to the connections only, the tote itself being offered as a non-pressurised atmospheric container. Stating your scope in writing — instead of asking permission for it — is how quotation boundaries survive contact with a project.

STEP 6   

The Solution We Proposed — and the Six Questions Behind It

By the time we sent our proposal, every open point had been resolved — by us or in discussion with the client. Six questions had to be answered before a number was final.

  1. Chemistry → classification: Which products go in which tank? Which are dangerous goods (UN 3265, PG II/III here) and which ship as general cargo? Is any tank itself a transport package (UN certification) or fixed equipment (none needed)?
  2. Material → SDS evidence: 304 + HDPE liner for all three media; bare 316 only where the biocide never sees it. Liner compatibility quoted against SDS Section 7, in writing.
  3. Liner → process: rotomoulded seamless HDPE as primary; PVC/CPVC sheet-lined as a priced option requiring a liner-maker’s compatibility statement.
  4. Mother–daughter → structure: free-standing bolted frame, 1,600 × 1,600 × 2,100 mm, load direct to ground, zero modification to the mother tote, knock-down shipping.
  5. Geometry → logistics: assembled height ≈ 3,245 mm → separate shipping, on-site assembly — confirmed before booking any container.
  6. Connections → ASME: B16.5 flanges / NPT threads / ASTM materials per the nozzle list; vessel offered as atmospheric.

TAKEAWAYS

Three Lessons Worth Stealing

1. The SDS is a design document, not a shipping form. Sections 7 and 14 decided the alloy, the liner polymer, the packing group and the labels. One afternoon of reading SDS lines saved the project from a 316 tank that would have failed with the biocide inside it.

2. “Mother–daughter” is a structure question disguised as a tank question. The client did not want a tank — they wanted 1.2 tonnes of standard IBC to hover safely above a 2–3 mm steel lid. The engineering answer (legs to the floor, bolted deck, locating stops) was cheap; the failure to engineer it would have been expensive.

3. Write your assumptions; don’t ask for permission. Quotation assumption clauses — “connections only, atmospheric vessel,” “shipped knock-down, assembled on site,” “daughter IBC quoted separately if required” — do more to protect margin and timeline than any follow-up email ever will.

Get A Better Solution Now

Our Sales Normally Reply Within 6 Hrs