A 3000 L Tank Used in Power Generation: What a Demineralised Water Break Tank Actually Has to Do
Ask what a 3000 L stainless tank is for and most people picture a tank farm — rows of vessels, bunded, branded, obvious. The more common reality is quieter. Ours went inside a 20-foot bunded container, alongside some pumps and filters, and became one component of a gas turbine package at a power station. You’d walk past it.
It has a specific job there, and the job explains everything about how the tank is built. It also explains why, three years after it shipped, an engineer at the site asked us a question we should have answered properly on day one.
1. What the tank is doing in a power station
The turbine needs demineralised water — water with the dissolved minerals stripped out, because mineral salts in the water will scale and corrode the hot gas path and the water/steam circuit. Producing that water is a chemical plant in miniature: filtration, reverse osmosis, mixed-bed ion exchange, monitoring.
A break tank sits between that water treatment plant and the turbine package. It is an atmospheric buffer — and it does four jobs at once:
- It breaks pressure. The treatment plant runs under its own pump pressure; the turbine package must never be back-pressurised by it. The tank creates an air gap, so downstream equipment sees only what its own pumps deliver.
- It breaks contamination. An atmospheric gap means treated water cannot be drawn back into the treatment plant, and plant water cannot be pushed forward.
- It buffers demand. The turbine’s draw is intermittent and spiky; the treatment plant prefers steady flow. Three thousand litres of storage decouples the two.
- It gives the pumps a stable suction source — a defined, vented, known-level reservoir rather than a live process line.
Note the phrase atmospheric buffer. That single word — atmospheric — decides the pressure question for this tank before anyone asks it. We’ll come back to that, because it’s where the story gets interesting.
2. Why there’s a desiccant filter on the vent
Demineralised water is pure, and pure water is strangely fragile. It has almost no buffering capacity, so it takes up atmospheric CO₂ readily:
CO₂ + H₂O → H₂CO₃
That carbonic acid drops the pH of demin water from around neutral toward 5.5, and — critically — it raises conductivity. On a plant that measures water quality in microsiemens, that’s not a cosmetic issue. It’s an out-of-spec reading, and in the worst case it’s carbonic acid corrosion of the carbon steel downstream.
So demin water tanks are often vented through a CO₂-absorbing desiccant — typically soda lime — to keep the stored water pure rather than merely clean. That’s why the filter exists. And that’s why the filter matters to the tank, because a desiccant bed is a restriction sitting in the one line the tank breathes through.
3. How this particular tank is built
The application sets the specification. A 3000 L demin water break tank that has to fit inside a shipping container and be lifted once ends up looking like this:
| Capacity | 3000 L |
| Tank body | 1800 L × 1300 W × 1500 H mm, 4 mm stainless shell |
| Frame | 80 × 80 × 3 mm square tube, legs shortened to suit container height |
| Approx. weight | 980 kg dry |
| Man access | DN400 man lid |
| Inlet | 2″ RFSO flange, 50 mm down from the top |
| Outlet / drain | 2″ with sloped floor to one end, valve and cam-lock |
| Level | DN150 sight glass + 2″ level sensor socket |
| Vent / relief | 1″ air vent, 1″ pressure relief valve |
| Clearance | 500 mm above the tank for man-lid access |
Every one of those choices is an answer to a constraint. The sloped floor to one end isn’t a detail anyone asks for — it’s what stops water sitting in the bottom of a tank that holds water measured in microsiemens. The shortened legs exist because the tank had to go into a container. The DN400 man lid exists because somebody, some year, will have to get inside with a torch.
And the 1″ vent and relief exist because the tank has to breathe — which is the part that came back to us in 2026.
4. Three numbers hide behind “what’s the pressure rating”
The 2023 enquiry asked one small question at the bottom of an email: “Also what is maximum pressure tank can be rated to.” We answered with a number in the margin of a drawing. The tank was built, tested, shipped.
Three years later, an engineer preparing to commission the package asked again — this time wanting the design code, the vent sizing basis, and confirmation that the tank was still rated correctly once a desiccant filter went on the vent.
The question came back because “pressure rating” means three different things, and we’d given one of them:
| What it is | This tank | |
| Design / max working pressure | What the shell is rated to hold | 0.1 MPa (1 bar / 14.5 psi) |
| Relief setting | Where the device opens — deliberately below the rating | +0.25 bar pressure, −0.03 bar vacuum |
| Service duty | What the tank sees in everyday operation | Atmospheric, vented — 0 kPa(g) |
Quote only the relief setting and you understate the tank fourfold. Quote only the design pressure and you’ve said what the shell can take but not what protects it. Say “atmospheric” and you’ve described the duty without giving a rating at all. All three are true. The job is saying which is which.
5. The arithmetic nobody does until commissioning
Here’s where the desiccant filter becomes more than a footnote.
A vacuum relief setting of −0.03 bar is −30 mbar. That’s the whole budget. A soda lime canister in good condition typically costs 10–20 mbar across it when dry and clean. Loaded with dust, or damp, it can spend the entire allowance on its own.
Once the filter is in the line, the margin the shell actually sees is what’s left after the filter — not the figure stamped on the relief valve. And a rectangular shell of 4 mm plate does something it doesn’t recover from when it’s pulled past its vacuum limit: the panels bow inward and stay bowed. There’s no reset.
Which gives the rule worth carrying into any tank specification:
A connection size is a dimension. A capacity is an answer. “1 inch” tells you nothing about whether the tank can breathe. “40 m³/h at 20 mbar across the installed restriction” does.
6. Five figures to ask for before a tank quote is accepted
If you’re specifying a break tank — or inheriting one — these decide whether it’s fit for duty. Ask before the PO, not before commissioning:
- Which design code, and does it match how the tank will be used, not just how it will be shipped?
- Maximum working pressure, numerically, with units.
- Relief settings — pressure and vacuum, stated as settings rather than ratings.
- Intended service duty, in words. Not “0 kPa”, but “atmospheric break tank, vented”.
- Vent capacity at the installed restriction, including anything you plan to bolt onto the vent.
Plus the one that costs nothing and prevents most of this: what is this tank not rated for?
7. What we changed
Ten minutes per quotation and a one-page document. Every tank we quote now carries a pressure and vacuum statement — design code, maximum working pressure, relief settings, intended duty in plain words, and an explicit list of what the unit is not rated for: pumped pressure, vacuum transfer, vacuum drying, steam or CIP under vacuum.
The last line is the one that earns its keep. An engineer who knows what a tank isn’t rated for will never use it that way by accident — and nobody has to reconstruct it three years later from a drawing margin.
LEETA METALS builds custom stainless steel tanks, IBCs and containers for power generation, water treatment and process duty — designed, welded, tested and documented to the code the application requires. Every unit ships with a pressure and vacuum statement.