A 40ft self-bunded container is one of the most efficient ways to store oils, lubricants and drums on a remote industrial site. This article sets out what the unit is used for, why it is usually specified instead of separate tanks or smaller containers, and how to define the right configuration before you request a quotation.
What a self-bunded container is
A self-bunded container carries its own secondary containment. The floor of the unit is built as a sealed sump with a containment capacity that holds the full volume of the largest container stored inside — in this model, 5,000 litres. Any leak, spill or drum failure stays inside the unit rather than reaching the ground, the drainage system or the surrounding workshop floor.
The unit is a single engineered structure. It is not a standard shipping container with a tray placed inside it, and it is not a bunded pallet or a drum rack. It is a purpose-built enclosure with structural integrity, a defined containment volume and configured openings.
Where the unit is used
Heavy-duty and mobile plant workshops. Engine oil, hydraulic oil, gear oil, coolant and lubricants all need to be kept close to the service bays without being kept on the floor. A self-bunded unit puts the oil store inside or beside the workshop and keeps the containment obligation in one place.
Mine sites and remote projects. Sites that operate under an environmental management plan generally need to demonstrate that hydrocarbon storage is contained. A self-bunded unit provides a containment boundary that can be inspected, labelled and recorded — and it can be relocated as the project moves.
Workshop builds with engineering certification. Where the oil store forms part of a workshop or shelter that requires engineering certificates — a dome shelter on a mine site, for example — the storage unit is treated as a structure. A single certified container is far simpler to document than an assembly of drums, trays, racks and separate tanks.
Temporary and relocatable facilities. Because the unit is built on container dimensions, it moves with standard heavy haulage equipment and can be lifted by forklift or crane at the designated points. Storage capacity can be added to a site and removed again without civil works.
Depots and laydown yards. For distributors and service providers holding oils across multiple locations, the unit standardises how the product is stored at every site, which simplifies auditing.
Why a single 40ft unit rather than 2 x 20ft
Two 20ft containers are cheaper to buy in many markets, and on a simple storage calculation they can offer comparable floor area. In practice, they are often not an acceptable substitute:
- Certification. If the unit is part of a certified workshop or shelter structure, the design approval covers one defined structure, not two separate ones.
- Containment. Two units mean two independent sumps, two sets of containment records and two spill response plans.
- Access. A 40ft unit opening along both long sides gives an uninterrupted working face for drum handling. Two 20ft units give you four narrower faces and a joint to work around.
- Handling. One lift, one delivery, one set-down position. Two units double the transport and cranage arrangements on a remote site.
A 20ft unit remains the right answer where the total volume is small and the site layout is constrained. The point is to size the unit to the actual inventory, not to the cheapest box available.
Two configurations: with and without a shelf rail
The same 40ft body is supplied in two versions.
Without the shelf rail. Single-level storage. Drums and IBCs sit on the bund floor. This is the more economical option and is the correct choice where the inventory is one layer deep and the operator has no intention of stacking.
With a single steel shelf rail. A 5mm plate shelf rail runs the length of the unit, creating a second storage level. Drums go on the floor and drums go on the shelf, which removes the need to stack drum on drum — a practice that is difficult to do safely, hard to inspect and frequently the source of handling injuries.
The decision is normally made on two questions: will you ever store IBCs or drums two high, and do you want the second level to be a fixed steel structure rather than a stack of pallets? If the answer to both is no, specify the unit without the shelf and reduce the cost.
Specification of the 40ft self-bunded unit
- Dimensions: 40ft high-cube — 12,192 × 2,438 × 2,896 mm. Where a single steel shelf rail is fitted, the unit is built at a custom height of 3,300 mm so that working clearance above the shelf is preserved.
- Containment: self-bunded, 5,000 litres (5 m³); the bund floor sits on a bottom cross-member of approximately 210 mm.
- Openings: both long sides open the full width. No doors on the short sides.
- Shelf: optional single steel shelf rail, 5mm plate.
- Application: oil and lubricant storage in workshops, mine sites, depots and remote facilities.
The full-width side opening is worth emphasising. It allows drums to be loaded and retrieved along the whole length of the unit rather than through a door at one end, which is the difference between a store that works in daily use and one that becomes a cupboard nobody wants to enter.
What to specify before requesting a quotation
Suppliers cannot quote this unit accurately from a photograph. The information that changes the design and the price is:
- What is going in it — 205L drums, 1000L IBCs, or both. Drum and IBC footprints require different internal arrangements.
- How many units, and whether the inventory will grow.
- Whether two-level storage is required, now or later.
- The port of discharge, and whether other cargo from the same origin can be consolidated into the same container. Consolidation is usually the largest single saving available on a single-unit shipment.
- The date the unit must be on site. This should be stated as a hard date, not a preference. A self-bunded unit in a non-standard configuration is built in a dedicated production slot rather than taken from stock, so lead time is the constraint that decides feasibility — and it is better to establish that at the beginning than after the specification is agreed.
Summary
A 40ft self-bunded oil storage container is the appropriate solution where oils and lubricants must be stored inside or adjacent to a working facility, where containment has to be demonstrable, and where the storage unit forms part of a structure that requires certification. The two configuration decisions — shelf rail or not, and single unit or multiple — should be made against the actual inventory and the actual site, not against the purchase price alone.